Qubino Z-Wave Plus Flush 1D Relay with Dry Contact Switch ZMNHND3

$ 54.95 $ 51.95
Availability: Out Of Stock

Smart Home Automation
 Qubino,Smart Home
Braeburn Digital Thermostat
Programmable wi fi thermostat
Affordable wifi thermostat

Always looking for the remote controller to open the gate? Or do you often wonder if you closed the garage doors, after leaving home? With Qubino Flush 1D Relay you can wirelessly control your garage door, gate, or entrance door of different power supply (110-240 VAC or 24 VDC). Use it to manage your gas water heater or as an intermediary that sends a PV signal to your heat pump, so it starts using photovoltaics energy and heating water to a higher temperature.


  • WHAT DOES IT DO? Install it behind your push-button garage opener switch, or at the low-voltage installation for your fireplace, or any dry contact circuit to get on/off Z-Wave control and status updates to your smart home hub.
  • WHAT ELSE DO I NEED? Check for NEUTRAL wire in the switch box (VERY IMPORTANT) if the connection to 120VAC. If powering the relay by 24 VDC, you'll need a separate power supply. You'll need a compatible Z-Wave hub to use this device (scroll down for details), like SmartThings, Vera, or Home Center Lite. Does NOT work with Wink or alarm panels. Alexa is NOT a Z-Wave hub.
  • DIVERSE INSTALLATION: It's so small, it will easily fit in any location and can be paired with a momentary or on/off wall switch for convenient local control. The relay adds to your system through auto-inclusion making the set-up quick and easy!
  • EXTRA FEATURES: Advanced configuration is available for expert users with open Z-Wave systems (parameter setting input required). THIS RELAY IS NOT SUPPORTED BY WINK, PIPER, OR ALARM PANELS (ADT Pulse, Vivint, Honeywell, Simon XT, and others).


      • Model Number: ZMNHND3
      • Z-Wave Signal Frequency: 908.42 MHz
      • Power: 120 VAC / 24 VDC
      • Maximum Load for 110VAC: 2300 W / 10A
      • Maximum Load for 24VDC: 240 W / 10A
      • Power Consumption: 0.4 W
      • Z-Wave Range: Up to 130 feet line of sight
      • Operating Temperature: 14-104° F
      • Installation and Use: Indoor only
      • Dimensions: 1.6" x 1.4" x 0.6"
      • Weight: 1 oz


Do NOT buy if your controller is not listed below. Contact Seller first.

    • Domoticz
    • Fibaro Home Center Lite
    • Home Assistant
    • HomeSeer
    • Samsung SmartThings Hub with custom device handler - Contact Seller for Instructions
    • VeraEdge
    • VeraPlus
    • VeraSec


    Technical specifications

    Power supply 110 - 240 VAC ±10%
    50/60Hz, (24-30 VDC)
    Rated load current of AC output (resistive load)* 1 X 10A / 240 VAC
    Rated load current of DC output (resistive load) 1 X 10A / 30 VDC
    Output circuit power of AC output (resistive load) 2300 W (230 VAC)
    Output circuit power of DC output (resistive load) 240 W (24 VDC)
    Digital temperature sensor range
    (sensor must be ordered separately)
    -25°C~+80°C (-13~ 176°F), resolution 0.1°C
    Operation temperature -10° ~ +40°C (14 ~ 104°F)
    Distance up to 30 m indoors (98 ft)
    (depending on building materials)
    Dimensions (WxHxD) 41.8 x 36.8 x 15.4 mm / 1,65x1,45x0,66 in
    (packaging) 74 x 43 x 86 mm / 2,91x1,69x3,39 in
    Weight (including packaging) 28 g (54 g) / 0.99oz (1.90oz)
    Electricity consumption 0.4 W
    For installation in boxes Ø ≥ 60 mm (2,36 in) or 2M, depth≥ 60 mm (2,36 in)
    Switching Relay

    * In the case of loads other than resistive, pay attention to the value of cosφ and if necessary use a load lower than the rated load. Max current for cosφ = 0.4 is 3 A at 250 VAC, 3 A at 24 VDC L/R = 7 ms.

    Supported Z-Wave Frequencies


    ZMNHND1 868.4 MHz
    ZMNHND2 921.4 MHz
    ZMNHND3 908.4 MHz
    ZMNHND4 869,0 MHz
    ZMNHND5 916,0 MHz
    ZMNHND6 868,4 MHz
    ZMNHND7 919,8 MHz
    ZMNHND8 865,2 MHz
    ZMNHND9 922,5 MHz
    ZMNHNDA 919,7 – 921,7 – 923,7 MHz
    ZMNHNDB 868,1 MHz
    ZMNHNDC 868,1 MHz
    ZMNHNDD 919,8 MHz
    ZMNHNDE 920,9 MHz


    Info and Guides